Linksys Router Not Working

Is your Linksys Router not working? If you are unable to use your Linksys router not working then here is the solution for your Linksys router. There is some common error can harm your router as well your internet. So if you are one of them and your Linksys router is not working, you can try these options or you can get help from officials as well.

Need Help - Request a call back now

Linksys Router Not Working

While many insist that Linksys is the best brand in home computer networking, there is no doubt that their software sucks, and you will undoubtedly encounter an issue at least one time throughout your ownership of a router & adapter combo.

This guide was made for you – and has been inspired by an episode I had, where my WRT54G router and WMP54G adapter refused to coincide with one another. As you won’t want my specific setup, this guide should help you determine whatever problem you have with your installation!

This manual was written while using a PC on Windows XP (if you are a Mac user, you are probably using some other magic quick fix, or may simply read this manual and work out how to do this in OSX! If you are using Vista or Win 7, then this manual should still give you the”gist” of finding out where your difficulty is).

How To Fix Linksys Router Not Working

Install the Router on one PC, Adapter on the 2nd PC

Sparing additional dialogue, here is a quick guide of the steps about Linksys Router Not Working and fix. I took to fix my problem and get my connection working. My upstairs computer with the router is successfully sending the signal to the downstairs computer, which is getting a signal through its adapter:

Installing the Router Driver on your 1st PC: Do not set up the Linksys software. Rather, save its drivers to a different folder on your desktop through the Linksys service page (you may use the drivers included on the CD that came with the router, even though the variation on Linksys’s site may be newer).

If your router isn’t already installed, join it by following the included instruction booklet. When you reboot your computer and it asks you if you want to install the driver, then you will have to stick to the choices for”Install drivers manually” or “Have a disk” and point it to the driver folder you have downloaded to your desktop computer.

Your PC will then install the drivers for your router, and that part of this manual is complete.

Installing the Adapter Driver in your 2nd PC:

Now, set up your adapter on your next computer, which will get the signal from the router. Install the card as described in the documentation, but don’t set up the Linksys software. Instead, once more, copy the drivers to your desktop computer.

Be sure you’re using the ideal driver version for that specific card (as an example, be certain not to use a 4.1 driver to get a 4.0 adapter card). The adapter version should be on a tag right on the card itself.

Reboot your computer after installing the card. When Windows finds the hardware, then proceed through the driver installation procedure just as in step 1: select “Install drivers manually” or “Have a disk”, point it to the driver folder on your desktop, and it’ll install your software.

Configuring the Router’s Settings

Your router and router should now be installed into their respective computers, with the latest drivers. Now, it is time to configure your router.

Proceed to the PC that has the router attached to it, and start up your internet browser. Go to http://192.168.1.1/ – this will open up your router setup panel.

Follow the instructions below, ONLY taking a look at the sections I cite, and leaving everything else in its default!

  • “Setup” Tab/”Basic Setup” Sub-Tab: Set to “Automatic Configuration – DHCP.” Click on the radio button next to”Enable DHCP server”, and be sure that the”Maximum number of DHCP users” is set to a number that represents the number of computers which will be getting internet access on your home (for me personally, this amount was set to 2).

  • “Wireless” Tab/”Basic Wireless Settings” Sub-Tab: Wireless network-style ought to be set to”Mixed.” “Wireless Network Name” should be something you can remember – perhaps your first name and last initial. . .this is a really important part which you will need to reference later! Finally, set”Wireless SSID Broadcast” to Enable.

 

  • “Wireless” Tab/”Wireless Security” Sub-Tab: This component is completely up to you. Personally, I am using”WEP” mode, since I have an iPod Touch which connects to a wi-fi online connection, and it only disturbs WEP at 128 Bits. There is nothing wrong with this, so check it out as you follow this tutorial – you can always go back and change it to something else, such as”WPA Personal.”
    In terms of a passphrase, make a password this is the 2nd most important thing you will need to reference in the future. Click “Generate.” The password will create 4″ Keys”, you will just need to appear at”Key 1″ later.

  • “Wireless” Tab/”Wireless MAC Filter” Sub-Tab: Establish “Wireless Mac Filter” to”Enable.” Under” Permit Only, “select” Permit only PCs recorded to get the wireless network” (this disallows your next-door neighbor from stealing your wireless cable link!). Now, go to your 2nd PC, together with the adapter card in it. Click “Start” and “Run” in MS Windows. Type CMD and hit Enter, which will bring up a DOS prompt. Type ipconfig /all, and search for a MAC address (it will be known as a “Physical address” on the list and will look something like”01-A2-B3-E4-23-B5″. Write this down.
  • Return to the PC using the router attached to it, which has the router configuration screen open. Be sure you’re still on the screen under the “Wireless” Tab/ “Wireless MAC Filter” tab, and click on “Edit Mac Filter List”. Type in the MAC address/Physical address which you have written down from another PC, only a couple seconds before, anyplace on the pop-up list (MAC 01 is fine). Be certain you use the right format with the colons, do not use dashes. To put it differently, it should look something like 01:A2:B3:E4:23:B5. . .click “Save settings”

 

  • “Access Restrictions” Tab/” Internet Access” Sub-Tab: Next to “Status”, click “Enable.” Enter a policy name here – it is merely a user profile (as an example, MySecondPC will be fine). Click “Allow” alongside “PCs.” Make sure “Regular” and”24 hours” will also be assessed. Click”Save settings,” then make sure “MySecondPC” or whatever you chose to get a Policy Name is listed in the dropdown choice on the peak of the screen, next to “Internet Access Policy.” Now, your 2nd PC was granted access to your router, whereas everyone else in the range is limited, as they’re not on the access list (kind of like a virtual bouncer!)

Getting a Signal to Your Adapter

Your router installation is now complete. . .it’s time for another half of this battle – getting the sign to appear in your 2nd PC, which will be using the adapter card! REMEMBER: we are using Windows, not Linksys’s software!

Locating the router sign on the wireless network listing:

Double click on the”Network connections” icon on the lower right-hand side of the screen, in the Windows tray. It should bring up a display showing all the wireless signals in the area — ideally, such as the one being sent from your router (you’ll recognize it as it is going to be your first name and last initial, or whatever you called it in the previous steps of the guide).

If for any reason you can not find this “Network connections” window, it may be found in Start / Settings / Control Panel / Network.

If you see that your router’s sign on the list, double click it. If you do not see your router’s sign, something went wrong during your router installation – probably, your router has a “Wireless SSID Broadcast” set to “disable” inside the”Wireless/Basic Wireless Settings” menu of the router setup page. Go back and check it!

Linking to the sign with WEP Key 1:

Windows will now try to connect to the signal being broadcast from your router. If all goes well, you will find a dialog box asking for the”WEP Key” that we saw before, through the router installation.

Here is the auto-generated key that the router software translated after you set in that password and clicked”Generate,” as seen in”Configuring the Router’s Settings”, Step 3, above.

Recall how it generates 4 WEP Keys, but you will just have to recall Key 1? This is where you will have to return to your own PC using the router on it and click on the “Wireless” tab, and the “Wireless Security” tab. Start looking for “Key 1” and write it down on a sheet of paper. It is a ridiculously long string of 26 letters and numbers.

Type out Key 1 in the dialog box on the computer with the adapter. It will ask you to type it out twice, really – the next time is merely to confirm. Click OK, and your personal computer *should* connect to your router, and your problem is solved!

If the adapter isn’t linking to the sign, try typing in the WEP Key 1, making certain that your caps lock is on, which you have typed it correctly. It’s simple to mistype it, as it’s such a long thing to type in.

Leave a Reply

Your email address will not be published. Required fields are marked *