Epson Printer Not Printing

Epson Printer Not Printing: In case you have an Epson printer and your prints are coming out faint, incomplete, or streaked with lines, odds are you have a clogged nozzle a frequent problem many users have with Epson printers.

It is inevitable that print heads clog over time as small quantities of ink residue dry up and accumulate in the nozzles. Being judicious about replacing capsules immediately if the ink alert goes away can do a lot to prevent ink from drying within the nozzles, but you still may end up with one or a couple might still get clogged for another reason. Blocked printheads can occur regardless if you use original Epson or aftermarket cartridges.

Epson Printer Not Printing

Printheads clog because nozzles become blocked by either ink or air. Clogs usually happen when:

You don’t alter your ink cartridge immediately once you get a low ink warning and you keep printing until you see faded printouts. When you place with a fresh cartridge, your printer prepares the printhead for the brand new ink cartridge, which is called priming. Priming is when the printer pushes ink through the nozzles to force out air.

The disadvantage to this is sometimes the printer can push too much ink and the surplus would smear all over the printhead in which it ends up blocking more nozzles. When the smeared ink dries, you once again wind up with clogged nozzles and worse printouts than previously.

You do not turn your printer off. Ink dries up in the nozzles if you don’t use it frequently. Turning your printer triggers the printer to conduct a mini-cleaning cycle and receives the ink flowing again.

You do not use your printer frequently. As mentioned before, the ink dries up when unused so if you simply use your printer about two times a month, we recommend that you decide on a laser printer. Laser printers use toner powder and do not dry up.

Knowing the usual causes of clogged printheads can help you take the necessary actions to prevent them from occurring. As the old adage goes, prevention is always better than cure.

Epson Printer Not Printing

Methods to Clean Your Printhead

Assess your nozzles and run cleaning cycles using the menu on your printer until you start up your device and clean it manually.

Printhead Cleaning Cycles:

Epson printer models feature a fairly efficient cleaning cycle that will often clean out the nozzles in a couple of cycles. Bear in mind, however, the newer versions have more cleaning cycles that sadly use more ink each time. Here’s how to begin:

Before you do anything else, be sure that the printer is not showing any errors on the LCD display.
Press the Home button and then choose “Installation ” then pick “Care .”
Select “Printhead Nozzle Check”

Your printer will make a page with four colored grids developed to exemplify that nozzles are blocked (and which aren’t ).
If no openings are found, select done.
If there are gaps or any lines are faint, select “Clean the printhead” and continue.
Caution: Never turn your printer off in a cleaning cycle. Doing this can cause permanent damage to the device!

PLEASE NOTE: This method is specific to pick Epson Workforce, Artisan, and Sure Color model printers, but may be broadly applied across a number of diverse versions, including most Expression versions. Please consult with your printer manual if you have any questions regarding your individual printer. To get a visual look into the procedure, check out this useful YouTube tutorial for A3 and A4 design printers here.

Epson Printer Not Printing

If you run a couple of cycles with no improvement on your print quality, permit the printer to rest for many hours to six hours wait period is advocated by Epson. Following this, go through a cleaning cycle and see if that improves the print quality.

A good deal of people will continue running cleaning cycles before the mind clears, frequently running six or eight cycles, which might work–until the following morning, when all of the ink used in the cleaning cycles which accumulated on the mind melts and melts again. Naturally, doing so will make your clog worse over time–AND use up a great deal of ink.

Contact Epson for additional instruction if you’re under warranty and still not seeing an improvement. If you’re no longer under warranty, you can manually clean the pieces to clean out stubborn ink clogs.

Cleaning your printhead can be performed manually in one of many ways, some more complicated and challenging than others. Below are some common troubleshooting solutions that work on any Epson inkjet printer models, recorded from the simplest to the most involved.

Clean Sponges with Distilled Water:

  • Switch off the printer and open the top. You need to be able to observe the printhead assembly.
  • Try to find a little plastic lever, which will pop up when the printer is not printing, to the left of this meeting. Move it forward and down to release the printhead, then push the meeting to the right. It might just move an inch or less initially, but if you push it to a stop, it is going to click. This fully releases the meeting so that you can push it to the side.
  • If there’s absolutely no lever beside your printhead assembly, print a page with the top up and unplug the printer with the meeting in the middle, unlocked.
  • You should watch sponges, which save ink in the capsules in the carriage. With an eyedropper or plastic syringe, saturate the sponges with distilled water or Windex solution.
  • Move the meeting back over the sponges as far right as it will go.
  • Let the distilled water place for at least fifteen minutes. For the best results, consider letting the printer soak overnight.
  • Print six to eight pages packed with text and graphics until your prints are come out clean and crisp. If you’re still not getting great results, consider moving on to another step in cleaning your printhead.

Epson Printer Not Printing

Distilled Water in Ink Port

  • Remove the ink cartridges out of your printhead carriage.
  • With the ink cartridges eliminated, you will notice small cone-shaped indents that take the ink out of the cartridge into the printhead. These are ink interfaces, and there should be one for every color/black cartridge.
  • With an eyedropper or plastic syringe, place a few drops of distilled water or printhead cleaner to the ink port which might be plugged. Do not place cleaner into each one the ports! If you are unsure, which color is which, look at the bottom of the ink port for color residue. Normally, yellow is the color on the far right, and moving left is magenta, cyan, and, eventually, black on the left.
  • Replace ink cartridges and await the printer to establish the new cartridge. If any water or solution dripped in the printhead, wipe it up with a paper towel before proceeding.
  • Print out six to eight pages of text and graphics to test the clarity.

Still not getting good results? Try this following procedure:

Cleaning the Printhead with Paper Towels:

  • Turn off your printer.
  • Tear one sheet of paper towel in half and fold it lengthwise until it’s all about one-half inch wide.
  • Open the top of your printer and search for a rubber roller that transports paper via the feed system. This feed system is where the printhead runs over when printing.
  • Secure the paper towel into the roller using tape and apply several drops of distilled water or cleaner near the center of the towel.
  • Move the printhead assembly over the paper towel and let it rest for at least fifteen minutes. Allow time for the dried ink on the printhead to start to dissolve. With time, you will find an assortment of black ink on the paper towel–this is more than just the black ink, it is really a mix of all colors into one pool.
  • Repeat with new moist paper towels until you begin to see individual colors from every ink port. You might want to repeat the procedure several times to see fantastic results.
  • Next, you might want to turn your printer back on. Before you do that, be sure that the printhead assembly has returned to its ready position, as opposed to resting in the middle.
  • Print several pages to be certain all those ports are cleared.

Leave a Reply

Your email address will not be published. Required fields are marked *